Editing Hard disk drive (section)

=== Magnetic recording ===
{{See also|Magnetic storage}}

A modern HDD records data by magnetizing a thin film of [[ferromagnetic material]]{{Efn|Initially gamma iron oxide particles in an epoxy binder, the recording layer in a modern HDD typically is domains of a granular Cobalt-Chrome-Platinum-based alloy physically isolated by an oxide to enable [[perpendicular recording]].<ref>{{Cite arXiv |title=New Paradigms in Magnetic Recording |eprint = 1201.5543|last1 = Plumer|first1 = M. L.|last2 = van Ek|first2 = J.|last3 = Cain|first3 = W. C.|year = 2012|class = physics.pop-ph}}</ref>}} on both sides of a disk. Sequential changes in the direction of magnetization represent binary data [[bit]]s. The data is read from the disk by detecting the transitions in magnetization.  User data is encoded using an encoding scheme, such as [[run-length limited]] encoding,{{Efn|Historically a variety of run-length limited codes have been used in magnetic recording including for example, codes named [[Frequency modulation|FM]], [[Modified Frequency Modulation|MFM]] and [[Group Coded Recording|GCR]] which are no longer used in modern HDDs.}} which determines how the data is represented by the magnetic transitions.

A typical HDD design consists of a ''{{visible anchor|spindle|Spindle}}'' that holds flat circular disks, called [[hard disk drive platter|platters]], which hold the recorded data. The platters are made from a non-magnetic material, usually [[aluminum alloy]], [[glass]], or [[ceramic]]. They are coated with a shallow layer of magnetic material typically 10–20 [[nanometer|nm]] in depth, with an outer layer of carbon for protection.<ref name="headcrash" /><ref name="AutoMK-6" /><ref name="AutoMK-7"  /> For reference, a standard piece of copy paper is {{convert|0.07|-|0.18|mm|nm|sp=us|abbr=on}}<ref name="AutoMK-8" /> thick.

[[File:Toshiba MK1403MAV - broken glass platter-93375.jpg|thumb|left|Destroyed hard disk, glass platter visible]]
[[File:Hard drive-en.svg|thumb|left|Diagram labeling the major components of a computer HDD]]
[[File:Aufnahme einzelner Magnetisierungen gespeicherter Bits auf einem Festplatten-Platter..jpg|thumb|Recording of single magnetisations of bits on a 200&nbsp;MB HDD-platter (recording made visible using CMOS-MagView)<ref name="AutoMK-9" />]]
[[File:Perpendicular Recording Diagram.svg|thumb|Longitudinal recording (standard) & [[perpendicular recording]] diagram]]

The platters in contemporary HDDs are spun at speeds varying from {{val|4200|ul=rpm}} in energy-efficient portable devices, to 15,000&nbsp;rpm for high-performance servers.<ref name="AutoMK-10" /> The first HDDs spun at 1,200&nbsp;rpm<ref name="IBM350" /> and, for many years, 3,600&nbsp;rpm was the norm.<ref>{{cite web |url=https://www.karlstechnology.com/blog/hard-drive-spindle-speed/ |title=Hard Drive Spindle Speed |publisher=The PC Guide |last=Kozierok |first=Charles |access-date=May 26, 2019 |date=October 20, 2018 |archive-url=https://web.archive.org/web/20190526103244/https://www.karlstechnology.com/blog/hard-drive-spindle-speed/ |archive-date=May 26, 2019 |url-status=live }}</ref> {{As of|November 2019}}, the platters in most consumer-grade HDDs spin at 5,400 or 7,200&nbsp;rpm.

Information is written to and read from a platter as it rotates past devices called [[disk read-and-write head|read-and-write heads]] that are positioned to operate very close to the magnetic surface, with their [[flying height]] often in the range of tens of nanometers. The read-and-write head is used to detect and modify the magnetization of the material passing immediately under it.

In modern drives, there is one head for each magnetic platter surface on the spindle, mounted on a common arm. An actuator arm (or access arm) moves the heads on an arc (roughly radially) across the platters as they spin, allowing each head to access almost the entire surface of the platter as it spins. The arm is moved using a [[voice coil]] actuator or, in some older designs, a [[stepper motor]]. Early hard disk drives wrote data at some constant bits per second, resulting in all tracks having the same amount of data per track, but modern drives (since the 1990s) use [[zone bit recording]], increasing the write speed from inner to outer zone and thereby storing more data per track in the outer zones.

In modern drives, the small size of the magnetic regions creates the danger that their magnetic state might be lost because of [[superparamagnetism|thermal effects]]⁠ ⁠— thermally induced magnetic instability which is commonly known as the "[[superparamagnetic limit]]". To counter this, the platters are coated with two parallel magnetic layers, separated by a three-atom layer of the non-magnetic element [[ruthenium]], and the two layers are magnetized in opposite orientation, thus reinforcing each other.<ref name="AutoMK-15" /> Another technology used to overcome thermal effects to allow greater recording densities is [[perpendicular recording]] (PMR), first shipped in 2005,<ref name="AutoMK-16" /> and {{as of|2007|lc=on}}, used in certain HDDs.<ref name="AutoMK-17" /><ref name="AutoMK-18" /><ref name="AutoMK-19" /> Perpendicular recording may be accompanied by changes in the manufacturing of the read/write heads to increase the strength of the magnetic field created by the heads.<ref>{{cite web | url=https://patents.google.com/patent/US20080002290 | title=Damascene coil design for a perpendicular magnetic recording head }}</ref>

In 2004, a higher-density recording media was introduced, consisting of coupled soft and hard magnetic layers. So-called ''[[exchange spring media]]'' magnetic storage technology, also known as ''exchange coupled composite media'', allows good writability due to the write-assist nature of the soft layer. However, the thermal stability is determined only by the hardest layer and not influenced by the soft layer.<ref name=AutoMK-19a /><ref name=AutoMK-19b />

Flux control MAMR (FC-MAMR) allows a hard drive to have increased recording capacity without the need for new hard disk drive platter materials. MAMR hard drives have a microwave-generating spin torque generator (STO) on the read/write heads which allows physically smaller bits to be recorded to the platters, increasing areal density. Normally hard drive recording heads have a pole called a main pole that is used for writing to the platters, and adjacent to this pole is an air gap and a shield. The write coil of the head surrounds the pole. The STO device is placed in the air gap between the pole and the shield to increase the strength of the magnetic field created by the pole; FC-MAMR technically doesn't use microwaves but uses technology employed in MAMR. The STO has a Field Generation Layer (FGL) and a Spin Injection Layer (SIL), and the FGL produces a magnetic field using spin-polarised electrons originating in the SIL, which is a form of spin torque energy.<ref>{{cite web | url=https://blocksandfiles.com/2021/06/14/toshiba-disks-get-2-gen-leg-up-from-flux-control/ | title=Toshiba disks get 2-gen leg-up from flux control | date=June 14, 2021 }}</ref>