Editing Mineral (section)

===Cleavage, parting, fracture, and tenacity===
{{main article|Cleavage (crystal)|Fracture (mineralogy)}}
[[File:Biotite-Orthoclase-229808.jpg|left|thumb|Perfect basal cleavage as seen in [[biotite]] (black), and good cleavage seen in the matrix (pink [[orthoclase]]).]]
By definition, minerals have a characteristic atomic arrangement. Weakness in this crystalline structure causes planes of weakness, and the breakage of a mineral along such planes is termed cleavage. The quality of cleavage can be described based on how cleanly and easily the mineral breaks; common descriptors, in order of decreasing quality, are "perfect", "good", "distinct", and "poor". In particularly transparent minerals, or in thin-section, cleavage can be seen as a series of parallel lines marking the planar surfaces when viewed from the side. Cleavage is not a universal property among minerals; for example, quartz, consisting of extensively interconnected silica tetrahedra, does not have a crystallographic weakness which would allow it to cleave. In contrast, micas, which have perfect basal cleavage, consist of sheets of silica tetrahedra which are very weakly held together.<ref name="DG39-40" /><ref name="ChL30-31">{{harvnb|Chesterman|Lowe|2008}}, pp. 29–30</ref>

As cleavage is a function of crystallography, there are a variety of cleavage types. Cleavage occurs typically in either one, two, three, four, or six directions. Basal cleavage in one direction is a distinctive property of the [[mica]]s. Two-directional cleavage is described as prismatic, and occurs in minerals such as the amphiboles and pyroxenes. Minerals such as galena or halite have cubic (or isometric) cleavage in three directions, at 90°; when three directions of cleavage are present, but not at 90°, such as in calcite or [[rhodochrosite]], it is termed rhombohedral cleavage. Octahedral cleavage (four directions) is present in [[fluorite]] and diamond, and [[sphalerite]] has six-directional dodecahedral cleavage.<ref name="DG39-40" /><ref name="ChL30-31"/>

Minerals with many cleavages might not break equally well in all of the directions; for example, calcite has good cleavage in three directions, but gypsum has perfect cleavage in one direction, and poor cleavage in two other directions. Angles between cleavage planes vary between minerals. For example, as the amphiboles are double-chain silicates and the pyroxenes are single-chain silicates, the angle between their cleavage planes is different. The pyroxenes cleave in two directions at approximately 90°, whereas the amphiboles distinctively cleave in two directions separated by approximately 120° and 60°. The cleavage angles can be measured with a contact goniometer, which is similar to a protractor.<ref name="DG39-40" /><ref name="ChL30-31"/>

Parting, sometimes called "false cleavage", is similar in appearance to cleavage but is instead produced by structural defects in the mineral, as opposed to systematic weakness. Parting varies from crystal to crystal of a mineral, whereas all crystals of a given mineral will cleave if the atomic structure allows for that property. In general, parting is caused by some stress applied to a crystal. The sources of the stresses include deformation (e.g. an increase in pressure), exsolution, or twinning. Minerals that often display parting include the pyroxenes, hematite, magnetite, and corundum.<ref name="DG39-40">{{harvnb|Dyar|Gunter|2008}}, pp. 39–40</ref><ref>{{harvnb|Chesterman|Lowe|2008}}, pp. 30–31</ref>

When a mineral is broken in a direction that does not correspond to a plane of cleavage, it is termed to have been fractured. There are several types of uneven fracture. The classic example is conchoidal fracture, like that of quartz; rounded surfaces are created, which are marked by smooth curved lines. This type of fracture occurs only in very homogeneous minerals. Other types of fracture are fibrous, splintery, and hackly. The latter describes a break along a rough, jagged surface; an example of this property is found in [[native copper]].<ref>{{harvnb|Dyar|Gunter|2008}}, pp. 31–33</ref>

Tenacity is related to both cleavage and fracture. Whereas fracture and cleavage describes the surfaces that are created when a mineral is broken, tenacity describes how resistant a mineral is to such breaking. Minerals can be described as brittle, ductile, malleable, sectile, flexible, or elastic.<ref>{{harvnb|Dyar|Gunter|2008}}, pp. 30–31</ref>